Lutron TGFSQ-FH-LA Instruction Manual download pdf

Español en el reverso

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299, U.S.A.

Made and printed in U.S.A. 9/01 P/N 033-041 Rev. D

Remove all inner

side sections

(shaded).

OFF

Installation

For installations involving more than one control in a wallbox, refer to

Multi-Unit Installations before beginning.

Step 1 WARNING: Turn power OFF at circuit breaker or remove

fuse.

Align control and

tighten screws.

OFF

Start screws.

• Easy-to-follow

Instructions

•

Instrucciones

Fáciles de Seguir

P/N 033-041

• Easy-to-follow

Instructions

•

Instrucciones

Fáciles de Seguir

P/N 033-041

Single Pole/3 Way

Quiet Fan-Speed Controls

AYFSQ-F: 1.5A maximum 120VAC, 60Hz

DVFSQ-F: 1.5A maximum 120VAC, 60Hz

DVFSQ-F-HO: 2A maximum 120VAC, 60Hz

DVSCFSQ-F: 1.5A maximum 120VAC, 60Hz

TGFSQ-F: 1.5A maximum 120VAC, 60Hz

Important Notes

Please read before installing.

1. CAUTION: To avoid overheating and possible damage to other

equipment, do not use to control receptacles, fluorescent lighting

fixtures, or transformer-supplied appliances.

2. Do not use control with a fan and light that operate with the same

switch.

3. When no "ground means" exists within the wallbox, then NEC 380-9

exception to (b) allows a control without a ground connection, to be

installed as a replacement. For this type of installation, cap or

remove the green control ground wire. A control installed under this

exception (NEC 380-9 exception to (b)) must be provided with a

plastic, noncombustible, UL listed wallplate.

4. Use control with a ceiling paddle fan only. Use only one ceiling

paddle fan per control.

5. For new installations, wire a test switch before installing the control.

6. Set multi-speed fans to their highest setting before installing

controls.

7. Do not wire controls in a circuit with a GFCI breaker/receptacle.

8. Use only one control in a 3-way circuit.

9. Install in accordance with all national and local electrical codes.

10. Clean control with a

soft damp cloth only

. Do not use any

chemical cleaners.

Multi-Unit Installations

When combining controls in one wallbox, remove all inner side sections

before wiring (see below). Use pliers to bend each side section up and

down until it breaks off. Reduction of control capacity is not required.

Step 2 Remove switch mounting screws. Pull switch from wall.

Step 3 Verify your application.

Step 4 Disconnect switch wires.

Ground

(Bare Copper or Green WIre)

Backwired:

Insert

screwdriver.

Pull wire out.

Terminal

Screws:

Turn screws

to loosen.

Step 6 Mount and align control. Install wallplate.

Step 7 Turn power ON.

SINGLE POLE:

Insulated wires

connected to two

screws of the same

color. See Step 5A.

3-WAY:

Insulated wires connected to three screws.

TAG insulated wire connected to the

different-colored (not green) screw or

screw labeled COMMON. See Step 5B.

Different-colored

screw (Common)

Ground

(Bare Copper

or Green WIre)

Tag

Step 5A Wire the control: in a SINGLE-POLE circuit

• Connect the green ground wire

on the control to the green or

bare copper ground wire in the

wallbox (see Important Note 3).

• Connect the black wire on the

control to either of the wires

removed from the switch.

• Connect the red wire on the

control to the remaining wire

removed from the switch.

• Using a wire connector, cap off

the red/white wire. This wire is

not used in a single pole circuit.

Step 5B Wire the control: in a 3-WAY circuit

• Connect the green ground wire

on the control to the green or

bare copper ground wire in the

wallbox (see Important Note 3).

• Connect the black wire on the

control to the tagged wire

removed from the different-

colored (not green) screw on the

switch.

• Connect the red wire on the

control to either of the remaining

wires removed from the switch.

• Connect the red/white wire on

the control to the remaining wire

removed from the switch.

120V

60Hz

Black Red

Red/White

Green

Ground

3-Way Switch

Fan

Neutral

Hot

Do not remove

side sections.

Limited Warranty

Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after

purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg,

PA 18036-1299, postage pre-paid.

THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF

MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER

THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE,

ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER

INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES

ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR

USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some

states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an

implied warranty may last, so the above limitations may not apply to you.

This product may be covered by Mexican patent 168,884 and one or more of the following U.S. patents:

4,833.277; 4,835,343; 4,835, 816; 4,947,054; 5,191,971; 5,207,317; 5,262,678; 5,293,103; 5,359,231; DES

342,234; DES 364,141 and corresponding foreign patents. Lutron is a registered trademark of Lutron

Electronics Co., Inc.

Technical Assistance

If you have questions concerning the installation or operation of this product, call the

Lutron Technical Support Center

. Please provide exact model number when

calling.(800) 523-9466 (U.S.A., Canada, and the Caribbean)

Other countries call (610) 282-3800

Fax (610) 282-3090 Internet: www.lutron.com

Important Wiring Information

Twist wire connector

tight.

Be sure no bare wire

is exposed.

When making wire connections, follow the recommended strip lengths and

combinations for the supplied wire connectors. Note: Wire connectors provided are

suitable for

copper wire only.

For aluminum wire, consult an electrician.

Small:

Strip insulation 3/8" for 14 AWG wire

Strip insulation 1/2” for 16 or 18 AWG wire

Use to join one 14 AWG supply wire with one

16 or 18 AWG control wire.

Large:

Strip insulation 1/2" for 10, 12 or 14 AWG wire

Strip insulation 5/8" for 16 or 18 AWG wire

Use to join one or two 12 or 14 AWG supply

wires with one 10, 12, 14, 16, or 18 AWG

control wire.

Small

Large

Green

Ground

Red/

White

Red

Black

Tag

Black

Ground

Red/

White

Red

Green

120V

60Hz

Black Red

Red/White

Green

Ground

Fan

Neutral

Hot

1 2

Summary of Contents

Page 1 - Quiet Fan-Speed Controls

Español en el reversoLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299, U.S.A.Made and printed in U.S.A. 9/01 P/N 033-041 Rev. DRe

Page 2 - Unipolar/Tres Vías

English on reverseLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299, U.S.A.Hecho e impreso en EE.UU., 9/01 P/N 033-041 Rev. DONOFF

Comments to this Manuals

No comments

Lutron TGFSQ-FH-LA Instruction Manual

Browse online or download Instruction Manual for Unknown Lutron TGFSQ-FH-LA. Lutron TGFSQ-FH-LA Instructions / Assembly User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Lutron TGFSQ-FH-LA